Labshake search
Citations for Molecular Devices :
501 - 550 of 732 citations for 3 2 5 Dioxoimidazolidin 4 yl propanoic acid since 2020
Citations are collected from bioRxiv only, the total number of publications could be much larger.
-
bioRxiv - Biophysics 2023Quote: ... Signals were lowpass filtered at 2 kHz by a 4-pole Bessel filter and acquired at a sampling rate of 10 kHz using a Digidata 1440A (Molecular Devices, USA). Data analysis was carried out in Clampfit 10 (Molecular Devices ...
-
bioRxiv - Physiology 2023Quote: Water samples were analysed for total ammonia (NH3/4 +) colourometrically (Verdouw et al.) in triplicate using a SpectraMax 190 microplate reader (Molecular Devices, USA) as in Sackville et al ...
-
bioRxiv - Cell Biology 2022Quote: ... CM-DCF fluorescence inside cells was measured at 485 nm for excitation and 538 nm for emission with FlexStation® 3 Multi-Mode Microplate Reader (Molecular Devices, Sunnyvale, CA, USA). The amount of emitted fluorescence was correlated to the quantity of reactive oxygen species (ROS) ...
-
bioRxiv - Bioengineering 2022Quote: ... was normalized to bacterial growth using optical density measured as absorbance at 600 nm (OD600) on a plate reader (Spectra Max 3, Molecular Devices, San Jose, CA, USA). Bioluminescent signals were quantified using the 8x12 grid ROI for all wells (in vitro thermocycler induction ...
-
bioRxiv - Microbiology 2021Quote: ... The plates were then incubated for 3 min at room temperature and the luminescence was assessed using a plate luminometer (Molecular Devices, San Jose, CA, USA) with 1 sec integration time ...
-
bioRxiv - Plant Biology 2023Quote: ... The plate was cooled for 3 min at room temperature before measuring the absorbance with a SpectroMax M5 UV/Vis spectrophotometer (Molecular Devices, San Jose, CA, USA) at 630 nm ...
-
bioRxiv - Plant Biology 2024Quote: ... LUC signals were measured using the Dual-Luciferase Reporter Assay Kit (Vazyme, Nanjing, China) and analyzed on a FlexStation 3 Multi-Mode Microplate Reader (Molecular Devices, San Jose, CA, USA). Relative luciferase activity was calculated based on LUC:REN ratios.
-
bioRxiv - Neuroscience 2021Quote: ... digitized at 10–20 kHz and low-pass filtered at 2–5 kHz with a Digidata 1440A analog-to-digital converter and analyzed off-line using Clampfit 10.7 software (Molecular Devices). Intrinsic excitability was determined in response to increasing depolarizing current pulses (+75 pA ...
-
bioRxiv - Biochemistry 2020Quote: ... Fluorescence intensity measurements were collected every 30 sec on a SpectraMax M5 fluorometer using Softmax Pro 5 software (Molecular Devices; excitation and emission set to 410 nm and 490 nm ...
-
bioRxiv - Neuroscience 2020Quote: ... The steady-state voltage responses were plotted against the amplitude of current injection and the slope of the linear fit between −5 pA to −30 pA was used to define Rin (Clampfit v. 11.1; Molecular Devices). Time constant (tau ...
-
bioRxiv - Microbiology 2021Quote: ... incubating 1 hour at 37ºC 5% CO2 and measuring fluorescence (λEX = 540 nm, λEM = 590 nm) on a SpectraMax M5 (Molecular Devices). The IC50 was calculated using GraphPhad Prism 9 using a non-linear regression analysis ...
-
bioRxiv - Pharmacology and Toxicology 2021Quote: ... was added and plates were gently shaken for 5 s to mix and then absorbance (O.D.) was measured at 450/620 nm on a SpectraMax M5 (Molecular Devices) instrument and data were processed by SoftMax Pro 6.4 software (Molecular Devices) ...
-
bioRxiv - Neuroscience 2021Quote: ... the data acquired at 5 kHz with a Digidata 1440A (Axon instruments) interface using pCLAMP 10 acquisition software (Molecular Devices). The Internal and external (bath ...
-
bioRxiv - Physiology 2021Quote: ... Currents were filtered at 1 kHz and digitized at 5 kHz using an Axopatch 200B amplifier and Clampex 10.4 (Molecular Devices. Offline analysis was performed using Clampfit 10.4 ...
-
bioRxiv - Neuroscience 2021Quote: ... Data were filtered at 5-10 kHz and digitized at 50 kHz using an acquisition board (Digidata 1440, Molecular Devices) attached to a personal computer running pCLAMP 10.2 software package (Molecular Devices) ...
-
bioRxiv - Immunology 2021Quote: ... DAF fluorescence intensities were measured every 5 minutes for a total of 60 minutes using a SpectraMax iD3 (Molecular Devices). All experiments were repeated at least four times per batch.
-
bioRxiv - Neuroscience 2022Quote: ... digitized at 5-20 kHz and acquired using a Digidata 1440A digitizer and pClamp 10 software (all from Molecular Devices).
-
bioRxiv - Neuroscience 2024Quote: ... Electrophysiological recordings were obtained from one neuron per slice and 4-5 slices per mouse using a Multiclamp 700B amplifier and analyzed using a digital system (pClamp version 11.2, Molecular Devices). Series and input resistances were monitored throughout the experiment using a -5 mV pulse ...
-
bioRxiv - Neuroscience 2024Quote: Currents were filtered at 5 kHz using low-pass Bessel filter of the amplifier and digitized using a Digitata 1,440 unit (Molecular Devices). All voltage clamp measurements were performed at a holding voltage of -60 mV ...
-
bioRxiv - Neuroscience 2024Quote: ... were plotted against the amplitude of current injection and the slope of the linear fit between −5 pA to −30 pA was used to define Rin (Clampfit v. 11.2; Molecular Devices). Time constant (tau ...
-
bioRxiv - Systems Biology 2022Quote: ... and the EtBr accumulation was measured by measuring the fluorescence in a microplate reader (spectramax multimode M 5, Molecular devices) at 37°C using 530 nm excitation wavelength and 585 nm as the emission wavelength ...
-
bioRxiv - Biochemistry 2023Quote: ... Data were sampled at 10 kHz and filtered at 5 kHz using a Digidata 1550A device controlled by pCLAMP 10.5 (Molecular Devices). Capacitance transients and leak currents were removed by subtracting a scaled control trace utilizing a P/4 protocol.
-
bioRxiv - Cancer Biology 2023Quote: ... Whole-cell currents were filtered at 5 kHz and digitized at 10 kHz using the software pCLAMP 10 (Molecular Devices). Micropipettes were pulled from Corning 8161 capillary glass tubes (Warner Instruments ...
-
bioRxiv - Neuroscience 2023Quote: Spontaneous IPSCs were detected and analyzed for 5-minute epochs during baseline and following drug exposure (Clampfit 11.1, Molecular Devices). For electrically-evoked IPSCs ...
-
bioRxiv - Neuroscience 2024Quote: ... Continuous current traces of 5-min duration (recorded at least 5 min after achieving whole-cell configuration) were acquired and analyzed with Clampfit 10.7 (Molecular Devices). The frequency and amplitude of recorded sIPSCs were quantified.
-
bioRxiv - Neuroscience 2024Quote: ... We detected the evoked qEPSCs 0.5-1.5s after the light onset and calculated the average number of qEPSCs from 5 sweeps using Clampfit 11 (Molecular Devices).
-
bioRxiv - Neuroscience 2021Quote: ... filtered at 2 kHz and digitized at 10 kHz with a MultiClamp 700B amplifier (Molecular Devices, CA, USA) and a Digidata 1550 digitizer (Molecular Devices) ...
-
bioRxiv - Neuroscience 2020Quote: ... low-pass filtered at 2 kHz using a Digidata 1550B low noise data acquisition system (Molecular Devices, USA). For whole-cell recordings ...
-
bioRxiv - Neuroscience 2021Quote: ... Recordings were made using an Axoclamp 2 B amplifier with HS-2A x0.1 headstage (Molecular Devices, CA, USA) and on a BX51WI Olympus microscope with a 40X LUMPlanFL/IR water immersion objective (Olympus Corporation ...
-
bioRxiv - Neuroscience 2020Quote: ... Signals were filtered at 2 kHz and sampled at 10 kHz with Digidata 1322A (Molecular Devices, Sunnyvale, CA). Patch pipettes made from thin-walled borosilicate glass (outer diameter 1.5 mm ...
-
bioRxiv - Neuroscience 2020Quote: ... Data were filtered during acquisition with a low pass filter set at 2 kHz using pClamp10 (Molecular Devices). Data analysis was performed offline with Clampfit 10.2 (Molecular Devices).
-
bioRxiv - Neuroscience 2022Quote: ... Data were filtered at 2 kHz and digitized at 20 kHz using a 1440A Digidata Digitizer (Molecular Devices). Series-resistance (<20 MΩ ...
-
bioRxiv - Neuroscience 2020Quote: ... Signals were low-pass filtered at 2 kHz and sampled at 10kHz with a Digidata 1440A (Molecular Devices). All data were stored on a computer for subsequent off-line analysis ...
-
bioRxiv - Neuroscience 2022Quote: ... low-pass filtered at 2 kHz and acquired using a Digidata 1550B and pClamp 10 software (Molecular devices). All reported voltages are corrected for a −13mV liquid junction potential calculated using Liquid Junction Potential Calculator in pClamp.
-
bioRxiv - Neuroscience 2023Quote: Image analysis methods to quantify relative ubiquilin 2 and TDP-43 aggregate deposition were developed in MetaMorph v7.10.5.476 (Molecular Devices), similar to those previously described [8 ...
-
bioRxiv - Cell Biology 2024Quote: ... Changes in fluorescence due to rise in intracellular Ca 2+ were monitored using FlexStation®III (Molecular Devices). Cells were simultaneously excited at 340 nm and 380 nm and emission was recorded at 5s intervals at 510 nm to determine Ca 2+-bound and Ca2+-free Fura-2 respectively ...
-
bioRxiv - Cell Biology 2023Quote: ... and videos were recorded at 2 frames/sec with 100ms exposure time using MetaMorph acquisition software (Molecular Devices). The excitation light was passed through a cyan excitation filter (Chroma) ...
-
bioRxiv - Biophysics 2024Quote: ... HEK293 cells were recorded at room temperature (25 ± 2 °C) using an Axopatch 200B amplifier (Molecular Devices, USA) with a holding potential of -60 mV ...
-
bioRxiv - Cell Biology 2024Quote: ... were mixed with 50 µL of Component A from the Fura-2 QBT Calcium Kit (#R6193, Molecular Devices) and incubated in the dark at room temperature for 30 min ...
-
bioRxiv - Neuroscience 2020Quote: ... Signals were filtered at 4–10 kHz and digitized at 10–20 kHz (Digidata 1322A and pClamp 10.2 Software; Molecular Devices, Sunnyvale, CA, USA). For analyses of K+-channel currents in NGFCs ...
-
bioRxiv - Neuroscience 2021Quote: ... amplifier and filtered online at 10 kHz with the built-in 4-pole Bessel filter and digitized at 20 kHz (Digidata1550B, Molecular Devices, CA, USA).)
-
bioRxiv - Cell Biology 2020Quote: ... incubated at 37°C for 4 h protected from light and read by a plate reader (Spectramax i3, Molecular Devices, Sunnyvale, CA, USA) at 585 nm using an excitation wavelength of 555 nm.
-
bioRxiv - Neuroscience 2021Quote: ... All recordings were filtered online at 10 kHz with the built-in 4-pole Bessel Filter and digitized at 20 kHz (Digidata1440, Molecular Devices, CA, USA). Traces were recorded in pCLAMP 9 (Molecular Devices ...
-
bioRxiv - Physiology 2023Quote: ... Relative changes in mag-fluo-4 fluorescence from baseline (F/F0) were recorded using Clampex 9.0 software (Molecular Devices, San Jose, CA, USA). The maximum rate of electrically evoked Ca2+ release was approximated from the peak of the first derivative of the mag-fluo-4 fluorescence (dF/dt ...
-
bioRxiv - Neuroscience 2024Quote: ... Signals were filtered at 4 – 10 kHz and digitized at 10 – 20 kHz (Digidata 1322A and pClamp 10 Software; Molecular Devices, Sunnyvale, CA). For cell attached recordings pipettes were filled with our standard extracellular solution.
-
bioRxiv - Neuroscience 2020Quote: Membrane currents from voltage-clamp electrophysiology experiments were amplified and low-pass filtered at 5 kHz using a MultiClamp 700B amplifier (Molecular Devices), digitized at 10 kHz and acquired using a Digidata 1550A digitizer (Molecular Devices) ...
-
bioRxiv - Cell Biology 2020Quote: ... were acquired at 20–100 kHz and filtered at 5–10 kHz (low-pass Bessel filter) using a computer attached to a DigiData 1200 (Molecular Devices). Patch pipettes were pulled from borosilicate glass (Kimble® Queretaro ...
-
bioRxiv - Cancer Biology 2022Quote: ... Blood samples were centrifuged to obtain plasma (300g for 5 min at room temperature) and OG fluorescence was read with a plate reader (FlexStation II Molecular Devices) at 480nm excitation/520nm emission.
-
bioRxiv - Neuroscience 2021Quote: ... 5-minute traces were recorded and mEPSCs events were detected using a template matching built-in feature in Clampfit (Molecular devices).
-
bioRxiv - Biophysics 2022Quote: ... The data was passed through a low-pass filter (1 kHz cutoff frequency) and stored in PC using an analog-to-digital converter (5 kHz sampling; Digidata 1550A; Molecular Devices) and pCLAMP software (Molecular Devices).