Labshake search
Citations for BioSpec :
1 - 15 of 15 citations for Cytochrome C Rabbit Recombinant mAb since 2019
Citations are collected from bioRxiv only, the total number of publications could be much larger.
-
bioRxiv - Molecular Biology 2022Quote: ... was homogenized at 4°C using 700 µL zirconia beads (BioSpec, 110791) in Precellys 24 homogenizer (Bertin Technologies ...
-
bioRxiv - Molecular Biology 2023Quote: ... Cells were disrupted for 1 minute at 4 °C in a Mini BeadBeater (BioSpec Products) with acid-washed glass beads ...
-
bioRxiv - Plant Biology 2020Quote: ... Samples were incubated at 80°C for 30 min with 0.5 mm zirconia/silica beads (Biospec) and vortexed several times at full speed for 10 min each to favour tissues disruption ...
-
bioRxiv - Molecular Biology 2022Quote: ... 10 mM β-mercaptoethanol) and lysed at 4 °C with glass beads in a BeadBeater (BioSpec). After centrifugation ...
-
bioRxiv - Microbiology 2020Quote: ... 2 min at 4°C between individual beating steps) using a Mini-Beadbeater-16 (Biospec Products, Bartlesville OK). Homogenized samples were centrifuged (12,000 x g ...
-
bioRxiv - Molecular Biology 2021Quote: ... Cells were pelleted at 6000 rpm for 2 minutes at 4°C and the pellet was resuspended in FA lysis buffer and Zirconia beads (0.7 mm diameter, Biospec). Cells were broken using a cell homogenizer (Bertin Instruments ...
-
bioRxiv - Genomics 2022Quote: ... Cells were lysed at 4°C by repeated vigorous agitation with 0.5mm zirconia/silica beads in a bead beater (Biospec) using 4 cycles of 60 s with 75 s of rest in between cycles ...
-
bioRxiv - Microbiology 2022Quote: Immediately after the fluorescence microscopy measurements (section 2.4), we dried (60 °C, 24 h) and ground (1 min, Mini bead beater 16; Biospec products) the 1.5 BSC disks used for the cyanobacteria/liverwort cover analysis and stored them at -80 °C for up to four months for DNA extraction ...
-
bioRxiv - Microbiology 2019Quote: ... a 96 well plate (Axygen P-DW-20-C) was loaded with 1 mL of 0.1 mm Zirconia Silica beads (Biospec 11079101Z) using a loading device (Biospec 702L) ...
-
bioRxiv - Genomics 2022Quote: ... Tubes were thawed at 70°C in a water bath after which 200 µL of 0.5 mm zirconia/silica beads (BioSpec Products) were added ...
-
bioRxiv - Genetics 2020Quote: ... were resuspended in 1 ml of 155 mM ammonium formate and lysed at 4 °C with 400 µl of acid-washed glass beads using a Mini-Beadbeater (Biospec). Lysates corresponding with 0.4 OD units were subsequently spiked with internal lipid standards and subjected to two-step lipid extraction [68] ...
-
bioRxiv - Genetics 2023Quote: ... Cells were lysed using a FastPrep (MP) bead beater (5 x 90 second runs at 4°C) and acid-washed glass beads (BioSpec), centrifuged ...
-
bioRxiv - Microbiology 2019Quote: ... This included a combination of 5 min of heat (65°C) followed by 5 min of bead-beating for cell disruption on a Mini-Beadbeater-24 (Biospec, U.S.A.). After extraction the DNA was checked for quality by gel electrophoresis and quantified using a Qubit 4 (Thermo Fisher Scientific ...
-
bioRxiv - Immunology 2023Quote: ... per kit instructions and included 2 cycles of 1 minute of bead beating at 4°C on a Mini-Bead-Beater 16 (BioSpec Products). The V3 and V4 regions of the 16S rRNA gene was amplified with a single round of PCR using primers that contained (described 3’ to 5’ ...
-
bioRxiv - Biochemistry 2023Quote: ... 4 °C) and then resuspended in 350 μl of Buffer A x Protease Inhibitors and ∼450 μl glass beads (1mm, BioSpec Products). The buffer solution should be enough to cover the beads by a thin layer ...